Sains Malaysiana 43(6)(2014): 909–914

 

Simulation and Statistical Approaches on Electrical Steel’s Magnetic Behaviour under

Unidirectional Single Sheet Tester

(Pendekatan Simulasi dan Statistik ke atas Kelakuan Magnet Keluli Elektrik di bawah

Satu Arah Penguji Kepingan Besi Tunggal)

NOOR ASHIKIN MOHD RASHID* & WAN NOR LIZA WAN MAHADI

 

Electromagnetic Radiation and Devices (EMRD), Block E, Department of Electrical Engineering

Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur, Malaysia

 

Received: 27 March 2013/Accepted: 2 December 2013

 

ABSTRACT

Evaluation of magnetic properties of electrical steel is vital in improving the quality of electrical machinery since it is used as magnetic cores for transformers, motors and generators. A double yoke single sheet tester (SST) was modeled using two identical C-cores wound with copper wires at limb side in horizontal arrangement. The magnetic properties for electrical steels, grade M4 and M19 were tested under a frequency of 50 Hz with the current ranging from 0.2 to 2.4A. The effects of the sample dimension and anisotropy on magnetic measurements were investigated. Evaluation on specimen dimensions indicate that the non-uniformity of sample magnetization in overhang sample can attribute to the flux leakage between the yoke legs. The stray flux is also increased with the overhang sample. However, the so-called fit-in sample which is fitted nicely between the yoke end poles can minimize the effect of stray flux. One way ANOVA and T-test were used as statistical methods and executed at the 5% significance level. It is statistically proven that the magnetic properties of both magnetic materials are influenced by their anisotropy.

 

Keywords: Anisotropy; magnetization; single sheet testerelectrical steel; stray flux

 

ABSTRAK

Penilaian sifat magnet keluli elektrik penting dalam meningkatkan kualiti jentera elektrik kerana ia digunakan sebagai teras magnet untuk transformer, motor dan penjana. Penguji kepingan besi tunggal (SST) yang diperbuat daripada dua teras-C yang sama saiznya, dililit dengan wayar tembaga di bahagian teras anggota secara mendatar. Sifat magnet keluli elektrik, gred M4 dan M19 diuji pada frekuensi 50 Hz dengan arus pada kadar 0.2 kepada 2.4A. Kesan dimensi sampel dan anisotropi ke atas pengukuran magnet dikaji. ANOVA satu hala dan ujian T digunakan sebagai kaedah statistik pada tahap kesignifikanan 0.05. Hasil statistik membuktikan sifat magnet untuk bahan magnet dipengaruhi oleh anisotropi bahan. Penilaian ke atas dimensi sampel menunjukkan ketidakseragaman pemagnetan sampel dalam sampel terjuntai yang mengakibatkan kebocoran fluks di kaki dening. Fluks yang terkeluar bertambah dengan penggunaan sampel terjuntai. Walau bagaimanapun, penggunaan sampel yang padan di antara hujung kaki dening berupaya mengurangkan kesan fluks yang terkeluar.

 

Kata kunci: Anisotropi; kebocoran fluks; keluli elektrik; pemagnetan; penguji kepingan besi tunggal

REFERENCES

ASTM. 2000. Standard test methods for alternating-current magnetic properties of materials at power frequencies using sheet-type test specimens A804/A804M-99 Annual Book of ASTM Standards: ASTM An American National Standard. pp. 170-177.

Fiorillo, F. 2010. Measurement of magnetic materials. Metrologia 47: S114-S142.

Graham, C.D. 1982. Physical origin of losses in conducting ferromagnetic materials (invited). Journal of Applied Physics 53(11): 8276-8280.

Moses, A.J. 2012. Energy efficient electrical steels: Magnetic performance prediction and optimization. Scripta Mater. http://dx.doi.org/10.1016/j.scriptamat.2012.02.027.

Nippon, S. 2011. Datasheet properties of electrical sheet steels. Magnetic Properties of TOA’s Electrical Sheet Steels. Nippon Steel. pp. 34-35.

Pluta, W.A. 2010. Some properties of factors of specific total loss components in electrical steel. IEEE Transactions on Magnetics 46(2): 323-325.

Stupakov, O., Kikuchi, H., Liu, T. & Takagi, T. 2009. Applicability of local magnetic measurements. Measurements 42: 706-710.

Stupakov, O. 2012. System for controllable magnetic measurement with direct field determination. Journal of Magnetism and Magnetic Materials 324: 631-636.

Tamaki, T., Fujisaki, K., Wajima, K. & Fujiwara, K. 2010. Comparison of magnetic field analysis methods considering magnetic anisotropy. IEEE Transactions on Magnetics 46(2): 187-190.

Weiss, N.A. 2005. Introductory Statistics. United States of America: Pearson Education Inc.

 

*Corresponding author; email: ashikin_rashid @yahoo.com

 

 

previous