Sains Malaysiana 47(4)(2018): 683-689

http://dx.doi.org/10.17576/jsm-2018-4702-05

 

Evaluation of Tensile Strength of Brazilian Test under Solid and Ring Disks using Finite Element Analysis

(Penilaian Kekuatan Regangan bagi Uji Kaji Brazil di bawah Cakera Utuh dan Cincin menggunakan Analisis Unsur Terhingga)

 

RINI ASNIDA ABDULLAH1* & TAKASHI TSUTSUMI2

 

1Faculty of Civil Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor Darul Takzim, Malaysia

 

2Urban Environmental Design and Engineering, National Institute of Technology, Kagoshima College, Hayato, Kirishima, Kagoshima 899-5193, Japan

 

Received: 20 June 2017/Accepted: 26 October 2017

 

 

ABSTRACT

 

The tensile strength of intact rock materials has been determined by indirect method more frequent than the direct method. The most commonly used indirect method is Brazilian test. Stress and deformability undergo during the test reflected by geometry shape of the samples with respect to the different diameter ratio. This study focuses on influence of geometry shape in solid and ring disk with different diameter ratio on the stress distribution and deformations within sandstone subjected to indirect tensile loading by Brazilian test. Then, the finite element method in RS2 software was utilised to simulate and gain in depth understanding the behaviour of Brazilian test. The analysis shown that the maximum tensile strength in a ring disk with diameter ratio of 0.1 is three times higher than in solid disk. Meanwhile, as the diameter ratio of ring disk increases, it produces lower tensile strength. The numerical simulation also has successfully illustrated the shear failure which observed near the loading platen of solid disk during Brazilian test. The finite element analysis utilised in this research has successfully enables the stress distribution and deformation behaviour of the rock under tension to be studied closely.

 

Keywords: Brazilian test; finite element method; ring test; RS2; tensile strength

 

 

ABSTRAK

 

Kekuatan regangan batuan utuh ditentukan dengan kaedah tidak langsung lebih kerap berbanding daripada kaedah langsung. Kaedah tidak langsung yang paling biasa digunakan adalah uji kaji Brazil. Tekanan dan perubahan bentuk yang dialami semasa uji kaji merujuk kepada bentuk geometri sampel dengan perkaitan nisbah diameter yang berbeza. Kajian ini memberi tumpuan kepada pengaruh bentuk geometri dalam cakera utuh dan cincin dengan nisbah diameter yang berbeza pada agihan tegasan dan perubahan bentuk di dalam batu pasir yang tertakluk kepada bebanan regangan tidak langsung dari uji kaji Brazil. Kaedah unsur terhingga di dalam perisian RS2 telah digunakan untuk mensimulasi dan memahami dengan lebih mendalam sifat uji kaji Brazil. Analisis menunjukkan bahawa kekuatan regangan maksima di dalam cakera cincin dengan nisbah diameter 0.1 adalah tiga kali lebih besar daripada cakera utuh. Sementara itu, semakin besar nisbah diameter cakera cincin, semakin kecil kekuatan regangan yang dihasilkan. Simulasi berangka telah berjaya menggambarkan tegasan ricih yang wujud berhampiran beban plat di dalam uji kaji Brazil pada cakera utuh. Analisis unsur terhingga yang digunakan dalam kajian ini telah berjaya membolehkan agihan tegasan dan perubahan sifat bentuk batuan di bawah tekanan untuk dikaji dengan teliti.

 

Kata kunci: Kaedah unsur terhingga; kekuatan regangan; RS2; uji kaji Brazil; uji kaji cincin

 

REFERENCES

Abdullah, R.A., Rosle, Q.A., Al-Bared, M.A.M., Haron, N.H., Shamsul Kamal, M.N.T. & Ghazali, M.H.Q. 2015. Stability assessment of rock slope at Pangsapuri Intan, Cheras. International Conference on Slopes, Malaysia. 14 -16 Sept. Kuala Lumpur.

Al-Bared, M.A.M., Abdullah, R.A., Yunus, N.Z.M., Amin, M.F.M. & Awang, H. 2015. Rock slope assessment using kinematic and numerical analyses. Jurnal Teknologi 77(11): 59-66.

Aresh, B., Daadbin, A. & Sarwar, M. 2016. Investigation into rock mechanics using finite element method. ISRM International Symposium - 6th Asian Rock Mechanics Symposium. 23-27 October, New Delhi, India.

Azlan, N.N.N., Simon, N., Hussin, A., Roslee, R. & Ern, L.K.E. 2017. Pencirian sifat kimia bahan tanah pada cerun gagal di sepanjang jalan Ranau-Tambunan Sabah, Malaysia. Sains Malaysiana 46(6): 867-877.

Chen, C.S. & Hsu, S.C. 2001. Measurement of indirect tensile strength of anisotropic rocks by the ring test. Journal Rock Mechanic & Rock Engineering 34(4): 293-321.

Cheng, Y. 2000. Slope stability analysis methods. Int. J. Rock Mech. Min. Sci. & Geomech. Abstr. 15: 50-58.

Chou, Y. & Chen, C. 2008. Determining elastic constants of transversely isotropic rocks using Brazilian test and interactive procedure. International Journal of Rock Mechanics & Mining Sciences 46: 219-234.

Erarslan, N., Liang, Z.Z. & Williams, D.J. 2012. Experimental and numerical studies on determination of indirect tensile strength of rocks. Journal Rock Mechanic & Rock Engineering 45(5): 739-751.

Gramberg, J. 1965. Axial cleavage fracturing, a significant process in mining and geology. Journal Rock Mechanic & Rock Engineering 1(1): 31-72.

Goh, T.L., Ghani, R.A. & Hariri, A.M. 2012. Kekuatan geomekanik batuan granit dan syis di Semenanjung Malaysia. Sains Malaysiana 41(2): 193-198.

Hague, T. 2010. Combined mode fracture via the cracked Brazilian disk test. Journal Rock Mechanic & Rock Engineering 18(4): 279-291.

Hobbs, D.W. 1964. The tensile strength of rocks. International Journal of Rock Mechanics & Mining Sciences 1: 385-396.

Hoek, E. 1964. Fracture of anisotropic rock. Journal of the South African Institute of Mining and Metallurgy 64(10): 501-518.

Hudson, J.A. 1969. Tensile strength and the ring test. International Journal of Rock Mechanics & Mining Sciences 6: 91-97.

ISRM. 2007. The Complete ISRM Suggested Methods for Rock Characterization, Testing and Monitoring 1974-2006: 212-218.

Kennedy, T.W. 1972. Practical method of conducting the indirect tensile test. Journal Rock Mechanic & Rock Engineering 42: 85-94.

Khalfalla, F.A.I. 2016. Reliability of indirect tensile strength test on homogenous material using finite element method. Master Thesis. UTM. pp. 19-70 (Unpublished).

Li, D., Ngai, L. & Wong, Y. 2013. The Brazilian disc test for rock mechanics applications: Review and new insights. International Journal of Rock Mechanics & Mining Sciences 46(2): 269-287.

Rocscience. 2016. RS2 User Manual. Rocscience Inc. Toronto. http://www.rocscience.com/. Accessed on April 2016.

Tsutsumi, T., Kukino, S., Abdullah, R.A. & Amin, M.F.M. 2016. Distribution of maximum principal stress under distributed load from loading plate in specimen for Brazilian test. Jurnal Teknologi 72(1): 1-6.

Yanagidani, T. 1978. The observation of cracks propagating in isotropic rock. Int. J. Rock Mech. Min. Sci. & Geomech. Abstr. 15: 225-235.

 

*Corresponding author; email: asnida@utm.my

 

 

 

 

previous