Sains Malaysiana 48(7)(2019): 1529–1537

http://dx.doi.org/10.17576/jsm-2019-4807-22

 

Morphology and Physical Properties of Ceramic Hollow Fibre Membrane: Effect of Different Bore Fluid Flow Rates

(Sifat Morfologi dan Fizikal Membran Serabut Berongga Seramik: Kesan Perbezaan Kadar Aliran Larik Cecair)

 

SITI SALWA ALIAS1, ZAWATI HARUN1,2*, AHMAD NAZREEN AHMAD ISMAIL1,2 & NOOR HASLIZA KAMARUDIN1,2

 

1Advanced Manufacturing and Materials Centre (AMMC), Institute Integrated Engineering (I2E), Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Johor Darul Takzim, Malaysia

 

2Department of Materials and Design Engineering, Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Johor Darul Takzim, Malaysia

 

Received: 6 November 2018/Accepted: 9 April 2019

 

ABSTRACT

The study on ceramic hollow fibre membrane (CHFM) has been extensively explored. In this study, the CHFM was fabricated via extrusion combined with phase inversion and sintering method using silica, alumina with polyethersulfone binder and N-Methyl-2-pyrrolidone solvent at different bore fluid flow rates (10, 15 and 20 mL min-1) and sintered (1200°C). The CHFM extruded at a flow rate of 10 mL min-1 and sintered (BF10-B) showed the good porous cross-sectional hollow surface compared to the dense agglomerated surface of BF15-B and BF20-B. The highest Rq (82.1 μm) and Ra (67.8 μm) were obtained from BF10-B based on topography analysis which corresponded to the higher pore entrances of the membrane. The porosity decreased inversely proportional with the density as the bore fluid flow rate increased confirming that the suppression of un-solidified particles in the inner region cannot occur completely at a high bore fluid flow rate and produced dense membrane. The fabricated CHFM in this study has the broad potential to be applied as a membrane for water separation since it meets the minimum requirement of a commercial ceramic membrane.

 

Keywords: Alumina; bore fluid; ceramic membrane; flow rate; silica

 

ABSTRAK

Kajian membran serabut seramik (CHFM) telah diterokai secara meluas. Dalam kajian ini, CHFM dibuat melalui penyemperitan yang digabungkan dengan penyongsang fasa dan kaedah pensinteran dengan menggunakan silika, alumina dengan pengikat polietersulfon dan pelarut N-Metil-2-pirolidon pada kadar larik cecair yang berbeza (10, 15 dan 20 mL min-1) dan disinter (1200°C). CHFM yang diekstrusi pada kadar aliran 10 mL min-1 dan disinter (BF10-B) menunjukkan permukaan keratan rentas berongga yang baik berbanding dengan BF15-B dan BF20-B yang mempunyai permukaan padat dan bergumpal. Nilai Rq tertinggi (82.1 μm) dan Ra (67.8 μm) diperoleh daripada BF10-B berdasarkan analisis topografi menunjukkan bukaan liang membran yang tinggi. Keliangan yang berkurangan berkadar songsang dengan ketumpatan kadar larik cecair yang meningkat mengesahkan bahawa penekanan zarah yang bersatu di kawasan dalam tidak dapat berlaku sepenuhnya pada kadar larik cecair yang tinggi dan menghasilkan membran yang padat. CHFM yang dibuat dalam kajian ini berpotensi untuk digunakan sebagai membran untuk penapisan air kerana ia memenuhi keperluan minimum membran seramik komersial.

 

Kata kunci: Alumina; kadar aliran; larik cecair; membran seramik; silica

REFERENCES

Alias, S.S., Harun, Z. & Ismail, N.F. 2019. Microstructure and physical characterization of alumina-sintered body via hot isostatic pressing. J. Aus. Ceram. Soc. Volume (Issue): 1-7.

Bao-li, L., Dan-ran, L., Jin-hui, C., Zeng-yong, L., Guang-hui, W., Xu-ping, Z., Fei, X. & Yan-qing, L. 2018. Hollow core micro-fiber for optical wave guiding and microfluidic manipulation. Sensor Actuat. B-Chem. 262: 953-957.

Chakraborty, S., Loutatidou, S., Palmisano, G., Kujawa, J., Mavukkandy, M.O., Al-Gharabli, S., Curcio, E. & Arafat, H.A. 2017. Photocatalytic hollow fiber membranes for the degradation of pharmaceutical compounds in wastewater. J. Environ. Chem. Eng. 5: 5014-5024.

Chen, Q., Wang, S. & Li, Z. 2012. Fabrication and characterization of aluminum silicate fiber-Reinforced hollow mesoporous silica microspheres composites. Micropor. Mesopor. Mat. 152: 104-109.

Harabi, A., Zenikheri, F., Boudaira, B., Bouzerara, F., Guechi, A. & Foughali, L. 2014. A new and economic approach to fabricate resistant porous membrane supports using kaolin and CaCO3. J. Eur. Ceram. Soc. 34: 1329-1340.

Honda, S., Ogihara, Y., Hashimoto, S. & Iwamoto, Y. 2010. Thermal shock properties of porous alumina for support carrier of hydrogen membrane materials. Advances in Bioceramics and Porous Ceramics III: Ceramic Engineering and Science Proceedings 31: 127-137.

Hubadillah, S.K., Othman, M.H.D., Ismail, A., Rahman, M.A., Jaafar, J., Iwamoto, Y., Honda, S., Dzahir, M.I.H.M. & Yusop, M.Z.M. 2018a. Fabrication of low cost, green silica based ceramic hollow fibre membrane prepared from waste rice husk for water filtration application. Ceram. Int. 44: 10498-10509.

Hubadillah, S.K., Othman, M.H.D., Matsuura, T., Rahman, M.A., Harun, Z., Jaafar, J. & Nomura, M. 2018b. Fabrications and applications of low cost ceramic membrane from kaolin: A comprehensive review. Ceram. Int. 44: 4538-4560.

Hubadillah, S.K., Othman, M.H.D., Harun, Z., Ismail, A., Rahman, M.A. & Jaafar, J. 2017a. A novel green ceramic hollow fiber membrane (CHFM) derived from rice husk ash as combined adsorbent-separator for efficient heavy metals removal. Ceram. Int. 43: 4716-4720.

Hubadillah, S.K., Othman, M.H.D., Harun, Z., Ismail, A., Rahman, M.A., Jaafar, J., Jamil, S.M. & Mohtor, N.H. 2017b. Superhydrophilic, low cost kaolin-based hollow fibre membranes for efficient oily-wastewater separation. Mater. Lett. 191: 119-122.

Hubadillah, S.K., Harun, Z., Othman, M.H.D., Ismail, A. & Gani, P. 2016a. Effect of kaolin particle size and loading on the characteristics of kaolin ceramic support prepared via phase inversion technique. J. Asian Ceram. Soc. 4: 164-177.

Hubadillah, S.K., Harun, Z., Othman, M.H.D., Ismail, A., Salleh, W.N.W., Basri, H., Yunos, M.Z. & Gani, P. 2016b. Preparation and characterization of low cost porous ceramic membrane support from kaolin using phase inversion/sintering technique for gas separation: Effect of kaolin content and non-solvent coagulant bath. Chem. Eng. Res. Des. 112: 24-35.

Hubadillah, S.K., Othman, M.H.D., Harun, Z., Ismail, A., Iwamoto, Y., Honda, S., Rahman, M.A., Jaafar, J., Gani, P. & Sokri, M.N.M. 2016c. Effect of fabrication parameters on physical properties of metakaolin-based ceramic hollow fibre membrane (CHFM). Ceram. Int. 42: 15547-15558.

Ismail, A.F. & David, L. 2001. A review on the latest development of carbon membranes for gas separation. J. Membrane Sci. 193: 1-18.

Ismail, N.F., Harun, Z. & Badarulzaman, N.A. 2012. A comparative study of double layers Al2O3/Al2O3 and Al2O3/ SiO2 prepared by microwave and natural drying. International Journal of Integrated Engineering 4: 16-21.

Jamalludin, M.R., Harun, Z., Othman, M.H.D., Hubadillah, S.K., Yunos, M.Z. & Ismail, A.F. 2018. Morphology and property study of green ceramic hollow fiber membrane derived from waste sugarcane bagasse ash (WSBA). Ceram. Int. 44: 18450-18461.

Jiang, W., Li, K., Xiao, J. & Lou, L. 2017. Effect of silica fiber on the mechanical and chemical behavior of alumina-based ceramic core material. J. Asian Ceram. Soc. 5: 410-417.

Kai-Fan, C., Pei-Yao, Z., Jia-Kai, W., Nai-Xin, W., Quan-Fu, A. & Kueir-Rarn, L. 2018. Polyelectrolyte complexes/silica hybrid hollow fiber membrane for fusel oils pervaporation dehydration processes. J. Membrane Sci. 545: 284-291.

Kingsbury, B.F. & Li, K. 2009. A morphological study of ceramic hollow fibre membranes. J. Membrane Sci. 328: 134-140.

Lee, M., Wang, B. & Li, K. 2016. New designs of ceramic hollow fibres toward broadened applications. J. Membrane Sci. 503: 48-58.

Lee, M., Wu, Z., Wang, R. & Li, K. 2014. Micro-structured alumina hollow fibre membranes-Potential applications in wastewater treatment. J. Membrane Sci. 461: 39-48.

Maaskant, E., de Wit, P. & Benes, N.E. 2018. Direct interfacial polymerization onto thin ceramic hollow fibers. J. Membrane Sci. 550: 296-301.

Tan, X., Liu, N., Meng, B. & Liu, S. 2011. Morphology control of the perovskite hollow fibre membranes for oxygen separation using different bore fluids. J. Membrane Sci. 378: 308-318.

Tan, X., Liu, Y. & Li, K. 2005. Preparation of LSCF ceramic hollow-fiber membranes for oxygen production by a phase-inversion/sintering technique. Ind. Eng. Chem. Res. 44: 61-66.

Wang, P. & Chung, T.S. 2012. Design and fabrication of lotus-root-like multi-bore hollow fiber membrane for direct contact membrane distillation. J. Membrane Sci. 421: 361-374.

Yu, X., An, L., Yang, J., Tu, S.T. & Yan, J. 2015. CO2 capture using a superhydrophobic ceramic membrane contactor. J. Membrane Sci. 496: 1-12.

Zhang, H., Li, B., Sun, D., Miao, X. & Gu, Y. 2018. SiO2-PDMS-PVDF hollow fiber membrane with high flux for vacuum membrane distillation. Desalination 429: 33-43.

Zhu, Z., Xiao, J., He, W., Wang, T., Wei, Z. & Dong, Y. 2015. A phase-inversion casting process for preparation of tubular porous alumina ceramic membranes. J. Eur. Ceram. Soc. 35: 3187-3194.

 

*Corresponding author; email: zawati@uthm.edu.my

 

 

previous