Sains Malaysiana 34(1): 57-61 (2005)

 

Penambahan Gentian Aramid (Twaron) dalam Adunan NR/LLDPE

dan ENR/LLDPE terhadap Sifat Mekanik Komposit

(Aramid Fibre (Twaron) Loading in NR/LLDPE and ENR/LLDPE

Blends on Mechanical Properties of the Composites)

 

 

Ishak Ahmad, Norul Azwan Din, Affendi Mohamad

Azizah Abdul Aziz & Ibrahim Abdullah

Pusat Pengajian Sains Kimia dan Teknologi Makanan

Fakulti Sains dan Teknologi

Universiti Kebangsaan Malaysia

43600 UKM Bangi, Selangor D.E., Malaysia

 

 

 

ABSTRAK

 

Penyediaan adunan getah asli termoplastik dan getah asli terepoksida termoplastik yang diperkuat dengan gentian aramid telah dilakukan melalui proses adunan leburan. Gentian aramid yang digunakan adalah gentian pendek Twaron (Teijin-Twaron) yang dirawat dengan bahan pelekat epoksi dan resorcinolformaldehid latex (RFL). Hasil yang diperolehi menunjukkan bahawa kesan penambahan gentian aramid telah meningkatkan tegasan maksima, modulus regangan, kekuatan hentaman  dan kekerasan kedua-dua adunan tersebut tetapi menurunkan nilai terikan pada takat putus. Bagi adunan NR/LLDPE didapati komposisi gentian yang paling optima adalah pada 20%. Penambahan gentian aramid seterusnya hanya menurunkan sifat mekanik adunan. Sebaliknya bagi adunan ENR/LLDPE, didapati komposisi gentian melebihi 20% masih menunjukkan peningkatan tegasan maksima dan modulus regangan. Keputusan ini menunjukkan bahawa interaksi antaramuka gentian aramid dan matriks dalam adunan ENR/LLDPE lebih baik berbanding NR/LLDPE.

 

Kata kunci: Gentian aramid, adunan NR/LLDPE, adunan NR/LLDPE

 

 

ABSTRACT

 

Blends of fiber-reinforced rubber (FRR) based on natural rubber-thermoplastic (NR/LLDPE) and epoxidized natural rubber ­thermoplastic (ENR/LLDPE) reinforced by aramid fibre have been done using melt blending process. Twaron aramid fibres (Teijin-Twaron) used in this project were treated with epoxy adhesion activated and resorcinol formaldehyde latex (RFL). It was found that with increasing amount of aramid fibre led to increase the maximum stress, tensile modulus, impact strength and hardness of the composites while the strain at break decreased rapidly. The results show that the optimum composition of filler loading in NR/LLDPE blend is 20%. However, in the case of the ENR/LLDPE composite, the tensile strength and modulus increase with increasing amount of the fibre above 20%. The results indicate that the interfacial adhesion between ENR/LLDPE and aramid is better than for the NR/LLDPE.

 

Keywords: Aramid Fibre, NR/LLDPE blend, ENR/LLDPE blend  

 

 

RUJUKAN/REFERENCES

 

Amornsakchai, T., Sinpatanapan, B., Bualek-Limcharoen, S. & Meesiri, W. 1999. Composite of aramid fibre (poly-m­phenylene siohthalamide)-thermoplastic elastomers (SEBS): enhancement of tensile properties by maleated-SEBS compatibiliser. Polym. 40: 2993-2999.

Arencon, D. & Velasco, J. I. 2001. Tensile behaviour and fracture toughness of EPDM filled with untreated and silane-treated glass beads. J. Mater. Sci. 36:179-187.

Arroyo, M., Zitzumbo, R. & Avalos. 2000. Composites based on PP/EPDM blends and aramid short fibres. Morphology/behaviour relationship. Polym. 41: 6351-6359.

Brahimi, B., Ait-Kadi, A. & Ajji, A. 1994. Weld lines mechanical properties of injection molded polyethylene/polystyrene/ copolymer blends. Polym. Eng. & Sci. 34(15): 1202(19).

De Lange, P. J., Mader, E., Mai, K., Young, R. J. & Ahmad, I. 2001. Characterization and micromechanical testing of the interphase of aramid-reinforced epoxy composites. Comp. Part A: Appl. Sci. & Tech. 32: 331-342.

Fu, S.Y., Lauke, B., Mader, E., Yue, C. Y. & Hu, X. 2000. Tensile properties of short glass fiber and short carbon fiber-reinforced PPcomposite. Compos. 31(A): 1117-1125.

Hanafi Ismail. 2000. Pengisi dan penguatan getah. Pulau Pinang. Penerbit Universiti Sains Malaysia.

Ibrahim Abdullah, Sahrim Ahmad & Che Som Sulaiman. 1995. Blending of natural rubber with linear low density polyehtylene. J. Appl. Polym. Sci. 58: 1125-1133.

Ismail, H. & Suzaimah, S. 2000. Styrene butadiene rubber/ epoxidized natural rubber blends: dynamic properties, curing characteristics and swelling studies. Polym. Testing 19: 879-­888.

Kim, J. K. 1996. Effect of blending thermoplastic elastomer with natural rubber compound and studies of short fiber reinforced rubber composite. J. Appl. Polym. Sci. 61: 431-438.

Mahy, J., Jenneskens, L.W. & Grabandt, O.,1994. The fibre/matrix interphase and adhesion mechanism of surface-treated Twaron aramid fibre. Compo 25: 653-659.

Perera, M. C. S., Ishiaku, U. S. & Ishak, Z. A. M. 2000. Thermal degradation of PVC/NBR and PVC/ENR50 binary blends and PVC/ENR50/NBR ternary blends studied by DMA and solid state NMR. Polym. Degrad. & Stability 68: 393-402.

Ratnam, C.T. & Khairul Zaman. 1999. Stabilization of poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends. Polym. Degrad. & Stability 65: 99-105.

Wal van der, A., Nijhof, R. & Gaymans, R. J. 1999. Polypropylene-­rubber blends: 2. The effect of the rubber content on the deformation and impact behaviour. Polymer 40: 6031-6044.

Wu, S.R., Sheu, G.S. & Shyu, S.S. 1996. Kevlar fiber-epoxy adhesion and its effect on composite mechanical and fracture properties by plasma and chemical treatment. J. Appl. Polym. Sci. 62:1347-1355.

Young, R. J., Bannester, D. J., Cervenka, A. J. & Ahmad, I. 2000. Effect of surface treatment upon the pull-out behaviour of aramid fibres from epoxy resins. J. Mater. Sci. 35: 1935-1947.

 

 

 

sebelumnya