Sains Malaysiana 48(4)(2019): 757–763

http://dx.doi.org/10.17576/jsm-2019-4804-07

 

Pencirian Geomekanik Jasad Batuan dan Analisis Kestabilan Cerun di Laman Granview, Saujana Puchong, Selangor, Malaysia

(Geomechanical Characterisation of Rock Mass and Slope Stability Analysis at Laman Granview, Saujana Puchong, Selangor, Malaysia)

 

ABDUL GHANI RAFEK2, ONG BOK CHENG1 & GOH THIAN LAI1*

 

1Program Geologi, Pusat Pengajian Sains Sekitaran dan Sumber Alam, Fakulti Sains dan Teknologi, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor Darul Ehsan, Malaysia

 

2Department of Geosciences, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, 31750 Tronoh, Perak Darul Ridzuan, Malaysia

 

Diserahkan: 28 Mac 2017/Diterima: 28 September 2017

 

ABSTRAK

Satu kajian pencirian geomekanik jasad batuan dan analisis kestabilan dua cerun terletak di tapak pembinaan Laman Granview di Saujana Puchong, Selangor telah dijalankan. Kawasan kajian merupakan sebahagian Formasi Bukit Kenny. Kajian telah dijalankan pada dua buah cerun potongan di tapak binaan adalah survei ketakselanjaran dan pencirian mekanik batuan. Kuarzit adalah litologi yang dominan di kawasan ini dengan sedikit filit. Ujian mekanik batuan berikut dijalankan: Ujian kekuatan mampatan sepaksi, ujian indeks beban titik dan ujian kekuatan regangan Brazil, ujian pantulan tukul Schmidt dan ujian Skleroskop Shore. Ujian kemiringan untuk penentuan kekasaran permukaan satah ketakselanjaran dijalankan pada sampel bongkah batuan. Hasil survei ketakselanjaran menunjukkan terdapat empat set ketakselanjaran yang utama di cerun L1 dengan nilai arah kemiringan/sudut kemiringan 62°/42°, 261°/79°, 281°/59° dan 237°/71°. Di cerun L2, terdapat tiga set ketakselanjaran utama iaitu dengan nilai arah kemiringan/sudut kemiringan 81°/41°, 171°/71° dan 198°/60°. Untuk ujian kemiringan, nilai purata sudut geseran puncak (fp) permukaan satah ketakselanjaran batu kuarzit dengan Pekali Kekasaran Kekar (PKK) 8-10 adalah 61°. Ketakselanjaran batuan kuarzit dengan nilai PKK 10-12 pula mempunyai purata sudut geseran puncak (fp) sebanyak 73°. Manakala, nilai purata sudut geseran puncak (fp) batuan filit dengan PKK 4-6 ialah 56°. Berdasarkan analisis kinematik, cerun L1 adalah stabil. Ragam kegagalan cerun L2 pula adalah kegagalan satah tetapi nilai sudut geseran permukaan satah yang tinggi akan menghalang kegagalan berlaku. Nilai perkadaran jasad batuan (RMR) bagi batuan kuarzit ialah 77 dan batuan filit ialah 66 dengan kedua-dua tergolong dalam batuan yang baik dalam kelas II.

 

Kata kunci: Analisis kinematik kestabilan cerun; perkadaran jasad batuan (RMR); ujian kemiringan

 

ABSTRACT

A study was conducted at the construction site of Laman Granview, Saujana Puchong, Selangor to study the stability of two slopes and the geomechanical properties of the rock mass. The study site is part of the Kenny Hill Formation. Surveys were carried out at two cut slopes at construction site were discontinuity surveys and rock mechanics characterisation. Quartzite is the dominant lithology in this area with minor amounts of phyllite. The following rock mechanics tests were conducted: Uniaxial compressive test, point load index test, Brazilian tensile strength test, Schmidt rebound hammer test and Shore Scleroscope test. Tilt tests for determining the surface roughness of discontinuities were conducted on rock block. The results of discontinuities survey showed that there are four major sets of discontinuities at cut slope L1 with dip directions/dip values of 62°/42°, 261°/79°, 281°/59° and 237°/71°. At cut slope L2, there are three major discontinuities sets with dip direction/dip values of 81°/41°, 171°/71° and 198°/60°. For the tilt test results, the average peak friction angle (fp) of the discontinuity surface for quartzite with Joint Roughness Coefficient (JRC) 8-10 is 61°. Discontinuity planes of quartzite with JRC of 10-12 have an average peak friction angel (fp) value of 73°, while phyllite with JRC 4-6 has an average peak friction angle (fp) value of 56°. Based on kinematic slope stability analysis, cut slope L1 is stable. Potential failure for cut slope L2 is plane failure but the high friction angle of the discontinuity surface will prevent failure. The Rock Mass Rating (RMR) obtained for quartzite is 77 and phyllite is 66 which both of which are classify as good rock mass in class II.

 

Keywords: Kinematic slope stability analysis; rock mass rating (RMR); tilt test

RUJUKAN

Abdul Ghani, R. & Goh, T.L. 2015. A systematic approach for the quantification of rock slope stability. Dalam Engineering Geology for Society and Territory Volume 2, disunting oleh Lollino, G., Giordan, D., Crosta, G.B., Corominas, J., Azzam, R., Wasowski, J. & Scirra, N. London: Springer.

Abdul Ghani, R. & Goh, T.L. 2012. Correlation of joint roughness coefficient (JRC) and peak friction angles of discontinuities of Malaysian Schists. Earth Science Research 1(1): 57-63.

Abdul Ghani Rafek, Siti Rashidah Mohd Rasid & Abdul Rahim Shamsudin. 2002. Sifat geologi kejuruteraan batuan kuarzit di Bangi Golf Resolf, Bandar Baru Bangi, Selangor Darul Ehsan. Bulletin Geological Society of Malaysia 45: 19-22.

Abdullah Sani, H.H. 1985. Discovery of an ammonoid (Agathiceras sp.) and crinoids stems in the Kenny Hill Formation of Peninsular Malaysia, and its significance. Warta Geologi 11(5): 205-209.

Ailie, S.S., Goh, T.L., Abdul Ghani, R., Azimah, H., Lee, K.E. & Tuan Rusli, M. 2017. Peak friction angle estimation from joint roughness coefficient of discontinuities of limestone in Peninsular Malaysia. Sains Malaysiana 46(2): 181-188.

Ailie, S.S., Goh, T.L., Abdul Ghani, R., Norbert, S., Azimah, H., Lee, K.E., Noraini, S. & Tuan Rusli, M. 2016. Development of empirical correlation of peak friction angle with surface roughness of discontinuities using tilt test. AIP Conf. Proceedings 060033(2016): https://doi. org/10.1063/1.4966871.

Bieniawski, Z.T. 1979. The geomechanics classification in rock engineering application. Proceedings of the 4th International Congress on Rock Mechanics 2: 41-48.

Brown, E.T. (pnyt). 1981. Rock Characterization Testing and Monitoring: ISRM Suggested Methods. Great Britain: Pergamon Press.

Deere, D.U. 1963. Technical description of rock cores for engineering purpose. Rock Mech. Eng. Geol 1: 18-22.

Goh, T.L., Abdul Ghani, R., Ailie, S.S., Azimah, H. & Lee, K.E. 2016a. Use of ultrasonic velocity travel time to estimate uniaxial compressive strength of granite and schist in Malaysia. Sains Malaysiana 45(2): 185-193.

Goh, T.L., Selim Reza, M., Abdul Ghani, R., Ailie, S.S., Azimah, H. & Lee, K.E. 2016b. Assessment of ultimate bearing capacity based on the Hoek-Brown failure criterion. Sains Malaysiana 45(11): 1603-1607.

Goh, T.L., Ainul, M.M.R., Nur Amanina, M., Abdul Ghani, R., Nur Ailie, S.S. & Tuan Rusli, M. 2016c. Rock slope stability assessment using slope mass rating (SMR) method: Gunung Lang Ipoh Malaysia. Scholar Journal of Engineering and Technology 4(4): 185-192.

Goh, T.L., Abdul Ghani, R., Ailie, S.S., Norbert, S., Lee, K.E. & Azimah, H. 2015a. Empirical correlation of uniaxial compressive strength and primary wave velocity of Malaysian Schists. Electronic Journal Geotechnical Engineering 20: 1801-1812.

Goh, T.L., Abdul Ghani, R., Ailie, S.S., Norbert, S., Azimah, H. & Lee, K.E. 2015b. Correlation of ultrasonic velocity slowness with uniaxial compressive strength of schists in Malaysian. Electronic Journal Geotechnical Engineering 20: 12663-12670.

Goh, T.L., Ghani Rafek, A. & Hariri Arifin, M. 2014a. Correlation of joint roughness coefficient with peak friction angles of discontinuity planes of granite, Peninsular Malaysia. Sains Malaysiana 43(5): 751-756.

Goh, T.L., Abdul Ghani, R., Ailie, S.S., Norbert, S. & Lee, K.E. 2014b. Empirical correlation of uniaxial compressive strength and primary wave velocity of Malaysian granites. Electronic Journal Geotechnical Engineering 19(E): 1063-1072.

Goh, T.L., Abdul Ghani, R. & Hariri, A. 2012. Geomechanical strength of granites and schists of Peninsular Malaysia. Sains Malaysiana 41(2): 193-198.

Google Map. 2017. Laman Granview. https://www.google.com/ maps/place/Laman+Granview,+47100+Puchong,+Selangor, +Malaysia. Diakses pada 27 Mac 2017.

Hoek, E. & Bray, J. 1981. Rock Slope Engineering. Edisi Ke-3. London: The Institution of Miningand Metallurgy.

Ibrahim Komoo & Ibrahim Abdullah. 1983. Ketakselanjaran dan kaedah pengukuran di lapangan. Sains Malaysiana 12(2): 119-140.

Ibrahim Komoo, Ibrahim, Abdullah & Juhari Mat Akhir. 1985. Ketakselanjaran dan kestabilan cerun batuan di Bukit Taman Melawati, Wilayah Persekutuan. Sains Malaysiana 14(1): 65-82.

Norbert, S., Rodeano, R., Abdul Ghani, R., Goh, T.L., Noran, N.N.A., Kamilia, S., Nightingle, L.M., Azimah, H. & Lee, K.E. 2016. Rock mass assessment using geological strength index (GSI) along the Ranau-Tambunan Road, Sabah, Malaysia. Research Journal of Applied Sciences, Engineering and Technology 12(1): 108-115.

Stauffer, P.H. 1973. Kenny Hill formation. Dlm Geology of the Malay Peninsula, disunting oleh Gobbet, D.J. & Hutchinson, C.S. New York: John Wiley & Son. Inc.

 

*Pengarang untuk surat menyurat; email: gdsbgoh@gmail.com

 

 

 

 

sebelumnya