Sains Malaysiana 40(7)(2011): 743–748

 

Effect of Molecular Weight on the Properties of Liquid Epoxidised Natural

Rubber Acrylate (Lenra)/Silica Hybrid Composites

(Kesan Berat Molekul ke Atas Sifat-sifat Komposit Hibrid Getah Asli

Terepoksida Berakrilat Cecair (LENRA)/Silika)

 

Eda Yuhana Ariffin* & Azizan Ahmad

School of Chemical Sciences and Food Technology, Faculty of Science and Technology

Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor D.E. Malaysia

 

Dahlan Hj Mohd, Mahathir Mohamed

Radiation Processing Technology Division (BTS), Malaysian Nuclear Agency, Bangi

43000 Kajang, Selangor D.E., Malaysia

 

Diserahkan: 23 Oktober 2009 / Diterima: 25 September 2010

 

 

ABSTRACT

 

This paper reports on the effect of molecular weight on the morphological and mechanical properties of liquid epoxidised natural rubber acrylate (LENRA)/silica hybrid composites prepared by sol-gel technique. The sol-gel reaction was conducted at different concentration of tetraethylorthosilicate (TEOS), used as a precursor of silica. TEOS were introduced in 10, 20, 30, 40 and 50 parts per hundred rubber (phr) in the composites. Two different molecular weights of ENR were used to study the effect of molecular weight on the mechanical and morphological properties of the compounds. These compounds were cured by ultraviolet (UV) irradiation. The mechanical properties were studied through pendulum hardness and scratch tests. Higher molecular weight of ENR showed better mechanical properties than lower molecular weight. Transmission electron microscope was used to determine the silica size and to study the distribution and dispersion of the silica particles. High molecular weight showed greater distribution and dispersion of silica particles with diameter of 13 nm–256 nm. Morphological and mechanical properties of LENRA/silica hybrid composites were improved by using high molecular weight of ENR.

 

Keywords: Epoxidised natural rubber; molecular weight; organic-inorganic hybrid; sol-gel technique

 

 

ABSTRAK

 

Kajian ini adalah mengenai kesan berat molekul terhadap sifat mekanik dan morfologi komposit hibrid getah asli terepoksida berakrilat cecair (LENRA)/silika, menggunakan teknik sol-gel. Tindak balas sol-gel dilakukan pada kepekatan tetraetilortosilikat (TEOS) yang berbeza, yang digunakan sebagai bahan pemula silika. TEOS dimasukkan sebanyak 10, 20, 30, 40 dan 50 bahagian per seratus getah (phr) dalam komposit. Dua berat molekul ENR yang berbeza digunakan untuk mengkaji kesan berat molekul terhadap sifat mekanik dan morfologi komposit. Komposit ini dimatangkan dengan menggunakan sinaran ultralembayung (UV). Sifat mekanik diuji melalui ujian kekerasan pendulum dan ujian calaran. Berat molekul ENR yang tinggi menunjukkan sifat mekanik yang lebih baik berbanding berat molekul ENR yang rendah. Mikroskop elektron transmisi digunakan untuk mengukur saiz silika dan mengkaji taburan partikel silika. Berat molekul yang tinggi menunjukkan taburan partikel silika yang lebih baik dengan diameter partikel dalam julat 13 nm-256 nm. Sifat mekanik dan morfologi komposit hibrid LENRA/silika dapat dibaiki dengan menggunakan berat molekul ENR yang tinggi.

 

Kata kunci: Berat molekul; getah asli terepoksida; hibrid organik-inorganik; teknik sol-gel

 

 

RUJUKAN

 

Abhijit, B., Anil, B. & Mousumi, D. 2004. Synthesis and characterization of acrylic rubber/silica hybrid composite prepared by sol gel technique. Journal of Applied Polymer Science 93: 2579-2589.

Akron & Wang, M.J. 1998. Effect of polymer-filler and filler-filler interactions on dynamic properties of filled vulcanizates. Rubber Chemistry and Technology 71: 520-567.

Amerio, E., Fabbri, P., Malucelli, G., Messori, M., Sangermano, M. & Taurino, R. 2008. Scratch resisstance of nano-silica reinforced acrylic coatings. Progress in Organic Coatings 62: 129-133.

Amerio, E., Sangerman, M., Malucelli, G., Priola, A. & Voit, B. 2005. Preparation and characterization of hybrid nanocomposite coatings by photopolymerization and sol-gel process. Polymer 46: 11241-11246.

Bandyopadhyay, A., Sarkar, M.D. & Bhowmick, A.K. 2004. Epoxidised natural rubber / silica nanoscale organic-inorganic hybrid composites prepared by sol-gel technique. Rubber, Chemistry and Technology 77: 830-846.

Bandyopadhyay, A., Sarkar, M.D. & Bhowmick, A.K. 2005. Epoxidised natural rubber/silica hybrid nanocomposites by sol-gel technique: Effect of reactants on the structure and the properties. Journal of Materials Science 40: 53-62.

Bandyopadhyay, A., Sarkar, M.D. & Bhowmick, A.K. 2006. Structure-property relationship in sol-gel derived polymer/silica hybrid nanocomposite prepared at various pH. Journal of Material Science 41: 5981-5993.

Bhowmick, A.K., Cho, J., MacArthur, A. & McIntyre, D. 1986. Influence of gel and molecular weight on the properties of natural rubber. Polymer 27: 1889-1894.

Chen, Z., Wu, L.Y.L., Shwa, E. & Tham, O. 2008. Scratch resistance of brittle thin films on compliant substrates. Material Science and Engineering A 413: 292-298.

Dahlan Hj Mohd & Abdul Ghani Harun 1993b. The use of natural rubber-based material for the preparation of radiation-curable resin II. Formulation and ultra-violet (UV) curing of low molecular weight epoxidised natural rubber acrylate (ENRA) – some basic studies. Nuclear Science Journal Malaysia 11 (1): 27-38.

Decker, C., Keller, L., Zahouily, K., & Bonfarhi, S. 2005. Synthesis of nanocomposite polymers by uv-radiation curing. Polymer 46: 6640-6648.

Frings, S., Meinema, H.A., Nostrum, C.F. & Linde, R. 1998. Organic-inorganic hybrid coatings for coil coating application based on polyesters and tetraethosilane. Progress in Organic Coatings 33: 126-130.

Fu, S.Y., Feng, S.Q., Lauke, B. & Mai, Y.W. 2008. Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate-polymer composites. Composites Part B: Engineering 39: 933-961.

He, J., Yan, B., Yu, B., Wang, S., Zeng, Y. & Wang, Y. 2007. The effect of molecular weight on properties of polymer-dispersed liquid crystals. European Polymer Journal 43: 2745-2749.

Heping, Yu., Zongqiang, Z., Guang, L., Qifang, W. 2008. Processing characteristics and thermal stabilities of gel and sol of epoxidized natural rubber. European Polymer Journal 44: 453-464.

Ishak Manaf. June 2001. Ceramers from aqueous polymer solutions of poly (ethylene oxide). Ph. D Thesis, Loughborough University, UK.

Kohjiya, S. & Ikeda, Y. 2003. In situ formation of particulate silica in natural rubber matrix by the sol-gel reaction. Journal of Sol-Gel Science and Technology 26: 495-498.

Kok, C.M. 1985. The effect of molecular weight on the physical properties of UV degraded natural rubber. European Polymer Journal 21(1): 37-40.

Noraiham, M., Muchtar, A., Mariyam, J.G., Dahlan, H.M. & Che Husna 2008. The effect of filler on epoxidised natural rubber-alumina. European Journal of Scientific Research 24: 538-547.

Patel, S., Bandyopadhyay, A., Vijayabaskar, V. & Bhowmick, A.K. 2005. Effect of microstructure of acrylic copolymer/terpolymer on the properties of silica based nanocomposites prepared by sol-gel technique. Polymer 46: 8079-8090.

Xiangmin, X., Binjie, Li., Huimin, Lu., Zhijun, Z. & Honggang, W. 2008. The effect of the interface structure of different surface-modified nano-SiO2 on the mechanical properties of nylon 66 composites. Journal of Applied Polymer Science 107: 2007-2014.

 

*Pengarang untuk surat-menyurat; email: edayu_hanna@yahoo.com

 

 

 

 

sebelumnya