Sains Malaysiana 43(2)(2014): 211–218

 

Investigation of Linearity between Mechanical Properties of Wood Using Graphical Method

(Analisis Hubungan Linear Beberapa Sifat Mekanik Kayu Menggunakan Kaedah Grafik)

 

 

MOHD JAMIL ABDUL WAHAB*1& MOHD ZAMIN JUMAAT2

 

1Makmal Kejuruteraan Kayu, Institut Penyelidikan Perhutanan Malaysia

52109 Kepong, Selangor, Malaysia

 

2Jabatan Kejuruteraan Awam, Fakulti Kejuruteraan, Universiti Malaya

50603 Kuala Lumpur, Malaysia

 

Received: 25 April 2012/Accepted: 26 May 2013

 

ABSTRACT

Some basic requirements are set for small clear specimen data to incorporate Malaysian timbers into equivalent European timber strength classes. In general, the correlation between structural and small clear specimen test results must be established for every timber group regardless of origin. This paper introduces a sort-plot technique for analysing the correlation of some mechanical properties of timber in selecting appropriate parametric model. Bending test was conducted on mixed species hardwoods for the determination of strength and stiffness values of both structural and small size specimens. The results showed that the sort-plot diagrams demonstrate an obvious linearity pattern between timber properties despite having poor regression values. The technique verified that properties of timber in structural and small size specimens correlated linearly

.

Keywords: Coefficient of determination; relationship; strength test

 

ABSTRAK

Beberapa syarat asas ditentukan ke atas data daripada spesimen bersaiz kecil untuk tujuan pengelasan kayu kayan Malaysia di dalam kumpulan kekuatan kayu Eropah. Secara umum, perhubungan antara hasil ujian spesimen bersaiz struktur dan kecil perlu ditentukan untuk setiap kumpulan kayu tanpa mengira negara sumber. Kertas ini memperkenalkan kaedah atur-plot untuk menganalisis perhubungan beberapa sifat mekanikal kayu dalam menentukan model parametrik yang bersesuaian. Ujian lenturan telah dijalankan ke atas beberapa spesies kayu keras untuk menentukan nilai kekuatan dan elastik spesimen kayu bersaiz struktur dan kecil. Keputusan ujian secara gambarajah atur-plot menunjukkan corak linear yang jelas antara sifat kayu walaupun mempunyai nilai regresi yang lemah. Kaedah tersebut mengesahkan bahawa sifat spesimen kayu bersaiz struktur dan kecil berkait secara linear.

 

Kata kunci: Hubungkait; pekali penentuan; ujian kekuatan

REFERENCES

Ahmad, Z., Bon, Y.C. & Abd Wahab, E.S. 2010. Tensile strength properties of tropical hardwoods in structural size testing. International Journal of Basic & Applied Sciences IJBAS-IJENS 10(3): 1-6.

Aicher, S., Hofflin, L. & Behrens, W. 2002. Determination of local and global modulus of elasticity in wooden boards. Otto Graf Journal 13: 183-198.

Alik, D. & Badorul Hisham, A.B. 2006. Strength performance of full-size structural timber of Dryobalanops species of Sarawak, Malaysia. Proceedings of the Nineth World Conference Timber Engineering. 6-10 August, Portland.

ASTM. 1952. Standard D143-52. Standard Methods of Testing Small Clear Specimens of Timber. Annual Book of ASTM Standards. Philadelphia.

Bostrom, L. 1999. Determination of the modulus of elasticity in bending of structural timber – comparison of two methods. European Journal of Wood and Wood Products 57(2): 145- 149.

BS 373:1957. Methods of Testing Small Clear Specimens of Timber. British Standards Institution, London.

Cleveland, W.S. & Devlin, S.J. 1988. Locally weighted regression: An approach to regression analysis by local fitting. Journal of the American Statistical Association 83(408): 596-610.

Desch, H.E. & Dinwoodie, J.M. 1996. Timber – Structure, Properties, Conversion and Use. 7th ed. Basingstoke: McMillan.

EN 408. 2003. Timber Structures - Structural Timber and Glued Laminated Timber. Determination of Some Physical and Mechanical Properties. European Committee for Standardisation, Brussels.

Engku, A.R.C. 1971. Basic and grade stresses for some Malaysian timbers. Malayan Forester 34(4): 131-134.

Kallsner, B. & Ormarsson, S. 1999. Measurement of modulus of elasticity in bending of structural timber. Proceeding of The First RILEM Symposium on Timber Engineering. 13-15 September, Stockholm.

Lanvin, J.D., Reuling, D., Rouger, F., van de Kuilen, J.W., Ravenshorst, G., Reinbol, G., Bourguignon, H., Gerar, J., Guibal, D., Verna, M. & Boilley, E. 2009. Simplified strength properties assessment for tropical hardwoods in view to CE marking. Proceedings of The Second International Scientific Conference on Hardwood Processing. 28-29 September, Paris.

Lee, Y.H., Engku Abdul Rahman, C. & Chu, Y.P. 1993. The Strength Properties of Some Malaysian Timbers. Timber Trade Leaflet No.34. Forest Department, Kuala Lumpur.

Madsen, B. 1992. Structural Behaviour of Timber. Timber Engineering Ltd., Vancouver,

Mansfield-Williams, H. 2010. Assistance with a Route to CE Marking for Malaysian Structural Timber. Report TE// F10260. TRADA Technology Ltd, High Wycombe.

Newlin, J.A. 1930. Factors to be Considered in Testing Structural Timbers. Madison: United States Department of Agriculture.

Ravenshorst, G. & van de Kuilen, J.W. 2010. Comparison of methods of strength classification of tropical hardwood timber. Proceedings of the Eleventh World Conference on Timber Engineering. 20-24 June, Riva Del Garda.

Saiful Bahari, B., Sarani, Z., Chin, H.C. & Mohd Jani, S. 2012. Liquefied residue of kenaf core wood produced at different phenol-kenaf ratio. Sains Malaysiana 41(2): 225–231.

Solli, K.H. 1996. Determination of modulus of elasticity in bending according to EN 408. Proceedings of the CIB-W18 Meeting. 26-29 August, Bordeaux.

Thomas, A.V. 1931. Some notes on timber testing. Malayan Forester 1: 56-59.

Watson, G.S. 1964. Smooth regression analysis. Sankhya. The Indian Journal of Statistics 26(4): 359-372.

Zaidon, A., Junaidi, B. & Faridah, M.T. 2001. Properties and durability of MUF-bonded particleboard treated with boron compound. Sains Malaysiana 30: 177-186.

 

 

*Corresponding author; email: mohdjamil@frim.gov.my

 

 

 

previous