Sains Malaysiana 38(2): 281-286(2009)  

Rekabentuk dan Implementasi Sistem Automasi Pembotolan MAPS menggunakan Programmable Logic Controller, PLC

(Design and Implementation Modular Automation Production  System-MAPS

using Programmable Logic Controller, PLC)

 

 

Riza Sulaiman, Anton Satria Prabuwono, Denni Kurniawan, Syaimak Abdul Shukor

Jabatan Komputeran Industri, Fakulti Teknologi dan Sains Maklumat,

Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor , Malaysia

 

Diserahkan: 13 June 2008 / Diterima: 07 August 2008

 

 

ABSTRAK

 

Kertas kerja ini membincangkan rekabentuk dan implementasi Programmable Logic Controller (PLC) untuk aplikasi miniatur pembuatan pembotolan (Modular Automation Production System - MAPS). PLC digunakan untuk menjalankan sistem supaya bekerja secara automatik dan digunakan untuk aplikasi sistem yang berulang. Penggunaan PLC dalam industri bertujuan meminimumkan kos pengeluaran, meningkatkan produktiviti, meningkatkan kualiti dan kebolehpercayaan sistem. Rekabentuk dan implementasi sistem automasi dilakukan dengan menggunakan MAPS. MAPS adalah suatu sistem modular yang dibangunkan dengan menggunakan beberapa stesen menjadi sistem terintegrasi. Di dalam kajian ini, MAPS digunakan sebagai miniatur pengeluaran pembotolan yang sebenar dan merupakan integrasi beberapa sistem iaitu PLC, pengesan, pneumatik, mekanik, elektronik dan sistem kawalan.

 

Kata kunci: Automasi; pembuatan pembotolan; MAPS; PLC

 

ABSTRACT

 

This paper discusses about design and implementation of Programmable Logic Controller (PLC) on Modular Automation Bottling Production System-MAPS. PLC is used for running a system so that it can work by way of automatic and always used on repeatable system application. The objectives of using PLC in industry are to minimize production cost, increase productivity, increase quality and system reliable. Design and implementation of this automation system uses MAPS. MAPS is a modular system that was developed by using a few stations into an integrated system. In this research, actual MAPS were used and integrates with other system such as detector, pneumatic, mechanic, electronic and control system 

 

Keywords: Automation;  bottling production; MAPS; PLC

 

RUJUKAN

 

Al-Khudairy, T. F., Al-Hashemy, B. A. R. & Al-Baker, M. A. J. 1998.  Design Of A Vmebus-Based Programmable Logic Controller (PLC). Microprocessors And Microsystems 21(5):  329-336.

Athani, V.V. 1984. CRT Terminal For Programmable Controller. Microprocessor and Microsystems 8(2): 80-85.

Away, Y. & Prabuwono, A.S. 2004. Aplikasi Teknologi Visi Mesin Di Industri. In Proc. Of Seminar Nasional Informatika (SNI). 337-343.

Bonfatti, F., Gadda, G. & Monari, P. D. 1995. Re-Usable Software Design For Programmable Logic Controllers. AMC Sigplan 30(11):  31-40.

Chirn, J. L. & Mcfarlane, D. L. 2000. Petry Nets Based Design Of Ladder Logic Diagrams. In Proc. Of The UKACC International Conference On Control.  1-6.

Ioannides, M. G. 2004. Design And Implementation Of PLC Based Monitoring Control System For Induction Motor. IEEE Transactions On Energy Conversion 19(3):  469-476.

MTAB Homepage. Atas Talian Http://Www.Mtabindia.Com, 1 Jun 2005.

Prabuwono, A.S. & Away, Y. 2004. Studi Sistem Visi Cerdas Untuk Kendali Mutu Menggunakan Modular Automation Production System (MAPS). In Proc. Of The 1st Conference On Telematic Systems, Services And Applications (TSSA) B-13: 75-80.

Saad, M., Hassane, H. S., Hasan, H., Guetioui, Z. E. & Cheriet, M. 2001. A Synchronous Remote Accessing Control Laboratory On The Internet. In Proc. Of International Conference On Engineering Education.  30-33. 

Siemens Homepage. Atas Talian Http://Www2.Automation.Siemens.Com/S7-200, 1 Jun 2005.

Wright, J.R. 1999. The Debate Over Which PLC Programming Language Is The State Of The Art. Journal Of Industrial Technology 5(4): 1-5.

Zhou, M.C. 1998. Design Of Industrial Automated System Via Relay Ladder Logic Programming And Petri Nets. IEEE Transactions On Systems, Man and Cybernetics 28(1): 137-150.

 

 

 

sebelumnya